Medical Products Supplies Companies

Via Canove 2/A, 26038 Torre dé Picenardi (CR)
Italy
Telephone +39 0375 394065
Fax +39 0375 394067
amministrazione@titanox.it
http://www.titanox.it

Product Categories

Product categories

01 Electromedical Equipment / Medical Technology
01.10 Hygiene / sterilisation / disinfection
01.10.01 Sterilisation equipment, disinfection equipment and accessories, autoclaves

Sterilisation equipment, disinfection equipment and accessories, autoclaves

Macerator TRITONE VAP – MOD. A4-TRITONEVAP
ALUMINIUM CONTAINERS WITH 1 VALVE
DRY HEAT STERILIZING UNIT mod. “SMALL”
Our products

Product category: Sterilisation equipment, disinfection equipment and accessories, autoclaves
Macerator TRITONE VAP – MOD. A4-TRITONEVAP
TRITONE VAP is a machine designed to shred disposable, sanitary containers made of paper and the organic
substances contained in them. This device washes and sanitizes the inner walls of the chamber and the shredding blades. Moreover this machine is equipped with a steam generator which disinfects them after shredding and washing.

• Door opening and closing is servo assisted.
• Automatic lock, during milling phase.
• Inner tank for water.
• Inner tank for detergent.
• Sensor for detergent tank level.
• Sensor for washing water tank level.
• Sensor for demineralised water tank level.
• Demineralised water automatic load.
• Discharge valve opening and closing is servo assisted.
• Ability to connect to the sewer drain through the wall or floor.
• The machine is fully controlled by microprocessor type DSP (digital signal processor).
• Graphic display 128×64 pixel.
• Backlit display.
• Description on display about the machine status and the type of alarm.
• Acoustic indicator for alarms.
• Green light indicator (operation).
• Red light indicator (alarms).
• Emergency button/STOP.
• Maximum cycle time: 8 min. (APPROX)
• Quantity of single-use containers per cycle: 1 to 6 max.
• Mill engine: 1, 5 kW.
• Electric pump: 0, 5 kW.
• Electric feeding: 230VAC 50Hz.
• Maximum power absorbed: 3500W
• Overall dimensions: 735x535x940 mm.

Directives and rules:
This machine is designed according to the following rules, where applicable:

• Direttiva/Directive/Directive/Directiva 2006/42/CE
• Direttiva/Directive/Direttiva/Directiva 2014/35/UE
• Direttiva/Directive/Directive/Directiva 2014/30/UE
• Norma/Rule/Norme/Norma CEI EN 61326.
• Norma/Rule/Norme/Norma CEI EN 60529.
• Norma/Rule/Norme/Norma CEI EN 60601-1.
• Norma/Rule/Norme/Norma CEI EN 61010-1.
• Norma/Rule/Norme/Norma CEI EN 61010-2-040.
• Norma/Rule/Norme/Norma CEI EN 62061
• Norma/Rule/Norme/Norma CEI EN 60417-2.
• Norma/Rule/Norme/Norma CEI EN 60204-1
• Norma/Rule/Norme/Norma ISO 15223-2
• Norma/Rule/Norme/Norma UNI EN 1717:2002.
• Norma/Rule/Norme/Norma UNI EN ISO 15883-1:2009.
• Norma/Rule/Norme/Norma UNI EN ISO 15883-3:2009.
• Norma/Rule/Norme/Norma UNI CEN ISO/TS 15883-5:2016.

Product category: Sterilisation equipment, disinfection equipment and accessories, autoclaves
ALUMINIUM CONTAINERS WITH 1 VALVE
The aluminium container with one valve offers a system which allows to carry out a mechanical filtering.
This system occurs in different phases which stand out for the placing of the valve.
The valve is in state of rest, before sterilization.
During the vacuum phase, the valve opens completely, so that the air escapes from the container. Then, the valve closes and the counter valve opens; in this phase steam enters and the sterilization phase begins. At the end of the cycle the valve closes airtight and this will maintain the load sterile inside the container.

GENERAL FEATURES
• Completely made of aluminium alloy 5005, thickness 2 mm. Body and lid completely pressed without welding.
Very sturdy.
• Gasket which ensures a perfect watertight, made of non-toxic silicone sponge that guarantees the maximum
seal. Lock with locking system against casual opening. Seal application system.
• Label-holder for storage and classification.
• Handles for transport.
• Guaranteed anodizing for natural colour or other colours, thickness 20 microns.
• Lid colours: grey, yellow, blue, red, green.
• Stacking system compatible also with other manufacturing houses.

FOR AN EXCELLENT OPERATION, WE SUGGEST YOU TO ALWAYS MAKE THE FOLLOWING CHECKS BEFORE
USING THE CONTAINERS:
• Lid gasket: check that the gasket is sufficiently elastic and that there are no cuts on it.
• Locks: check that the locks levers (hinges) sufficiently oppose the force supplied in the opening and that the pressure caused by the clamp is adequate to compress the silicon gasket.
• Valve: check the good functioning of the valve. It is necessary to open the lid and depress with a soft pointed rod the internal part of the valve, passing through the hole situated in the centre of the perforated aluminium plated.

Product category: Sterilisation equipment, disinfection equipment and accessories, autoclaves
DRY HEAT STERILIZING UNIT mod. “SMALL”
Outer case made of stainless steel.
Inner structure, grid, removable perforated tray, hinged lid completely
made of stainless steel. Inner structure and lid with nontoxic silicon rubber gasket, insulated by high grade glass wool. Stainless steel armoured heating element. Timer from 0 to 120 minutes, which disconnects the device at the end of the programmed time.
Probe thermometer 0° – 200°C. Probe thermo-regulator 0° -200°C. Safety thermostat.
Green pilot light (on the right) that
that shows the line insertion. Green
pilot light (on the left) that points out
the resistance operation.
230V – 50/60 Hz

ad: contact information

About Us

Company details
GLOBAL QUALITY SOLUTIONS

Founded in 1980, the TITANOX Co. of Torre de Picenardi (CR), Italy, has specialized right from the outset in the field of Hospital Medical Furniture & Instruments with the production and sales of electromedical items (devices and accessories for sterilization) and a wide range of stainless steel furniture and instruments for the Healthcare Industry. Quality and attention to details is the underlying factor for all the production process.

Selection of raw material, the choice of purchasing strictly from qualified suppliers, the best technical know-how & expertise in manufacturing process and the meticolous quality control procedures applied, are components which are fundamental to the quality-oriented reality of the TITANOX Co. The Company owns, freehold, a total of 20000 sq. meter area of which 6000 covered for workshop production and utilizes most advanced technology CNC Machinery equipment and plant systems, thanks to which the Company has affirmed itself as leader in medical equipment field both nationally and internationally.

The TITANOX Co. presently exports either directly or through a network of Distributors to more than 50 countries worldwide.
Constant efforts in the search for solution ever more oriented to better quality and consequently to better service to our Partner, the Costumer, assure the implementation of high-standard quality system in conformity to the norms of:

Quality System certified by notified body Kiwa Cermet Italia S.p.A. (Cadriano BO)

On request, it is possible to receive:
• copy of our ISO 13485: 2016 certificate
• copy of our ISO 9001: 2015 certificate
• copy of our CE certificate 0476_ MED 31461 which is valid for all our sterilizers

ad: company